If you need a broader overview of what a cable gland is and how materials and IP ratings fit into selection, start with What Is a Cable Gland?. For Japanese marine PF practice in depth, see JIS Marine Cable Gland Explained.
Why Cable Gland Thread Type Matters
The entry thread is the interface between the gland body and the enclosure wall. It must match the hole that was punched, tapped, or molded into the panel. A mismatch is one of the most common first-time-buyer errors in international procurement: a Metric gland will not correctly engage an NPT hole, and a PG body will not seat in a Metric knockout even when the major diameters look similar on a datasheet.
Wrong thread choice leads to three practical failures. First, the mechanical joint is weak or cross-threaded. Second, the panel-side O-ring or sealing face does not compress evenly, so the enclosure’s IP rating is lost at the entry. Third, field teams waste time on adapters that add another leak path and another tolerance stack. Specifying the thread the enclosure already has is almost always cheaper than correcting it on site.
The Five Common Cable Gland Thread Types
Metric (ISO 965 / EN 60423)
Metric threads are the dominant standard for new industrial equipment in Europe and much of Asia. Sizes are designated by major diameter and pitch, for example M20 × 1.5. The thread is parallel (straight), so environmental sealing at the panel face relies on an O-ring or gasket under the body flange, not on interference along the thread flanks.
Common cable gland sizes run from about M12 through M63 for general industrial work, with larger sizes available for heavy cable. Metric aligns with IEC entry practices and is the default choice for new EU and Asia-Pacific projects unless the enclosure drawing states otherwise. XingWei supplies Metric glands across brass, nylon, and stainless ranges in the cable gland category.
NPT (ANSI/ASME B1.20.1)
NPT (National Pipe Taper) is the North American default for many industrial enclosures and conduit fittings. The thread is tapered (approximately 1:16). As the male and female threads tighten, the flanks wedge together and can form a mechanical seal; PTFE tape or thread sealant is still commonly used in practice.
NPT sizes are inch-based (for example ½″ NPT, ¾″ NPT). They are not dimensionally compatible with Metric or PG of “similar” size. If the project is specified to the National Electrical Code and the enclosure is punched or tapped for NPT, order NPT glands—do not substitute Metric and hope an adapter will pass inspection.
PG (DIN 40430)
PG (Panzergewinde) is a German conduit thread with an 80° flank angle and a rounded profile. It was once the main European electrical entry standard. Metric has largely replaced it for new designs, but PG remains widespread on legacy machinery, older control cabinets, and spare-parts inventories.
Common sizes include PG7, PG9, PG11, PG13.5, PG16, PG21, and larger. There is no one-to-one conversion to Metric: major diameters and pitches differ, so a “PG11 ≈ M20” rule of thumb is only a rough guide for clearance, not a license to mix threads. For buyers who specifically need small PG entries, see the PG7 Cable Gland Selection Guide.
G / BSP (ISO 228)
G threads (often called BSP parallel) are parallel pipe threads used widely in the UK, Commonwealth markets, and hydraulic-influenced equipment. Like Metric, they do not seal on the thread flanks; sealing depends on a washer, O-ring, or face seal at the entry.
G sizes are designated in inches (for example G½, G¾). They are not the same as NPT: NPT is tapered, G is parallel, and the thread form differs. Mixing G and NPT is a frequent error on projects that span UK and North American supply chains.
PF (JIS) for Japanese Marine and Domestic Equipment
PF is the Japanese parallel pipe thread form used under JIS F 8801 for many marine and shipboard cable glands. It is a key differentiator for buyers serving Japanese yards, coastal fleets, and equipment built to Japanese industrial practice.
PF should not be treated as interchangeable with G/BSP or NPT without checking the drawing and the standard called out on the enclosure. For material selection (often 316 stainless in saltwater service) and F 8801 context, use the dedicated JIS marine cable gland guide.
Quick Comparison: Metric vs NPT vs PG vs G vs PF
| Thread | Standard | Form | Typical markets | Seal at entry |
|---|---|---|---|---|
| Metric | ISO 965 / EN 60423 | Parallel | EU, most of Asia, new global OEM | O-ring / flange gasket |
| NPT | ANSI/ASME B1.20.1 | Tapered | North America | Thread interference (+ sealant) |
| PG | DIN 40430 | Parallel (80° flank) | Legacy European equipment | O-ring / gasket |
| G / BSP | ISO 228 | Parallel | UK, hydraulics, Commonwealth | Washer / face seal |
| PF (JIS) | JIS F 8801 | Parallel | Japanese marine / domestic | Per marine gland design |
Cable gland threads follow different national standards: Metric (ISO 965) for most of Europe and Asia, NPT (ANSI B1.20.1) for North America, PG (DIN 40430) for legacy German equipment, G/BSP in the UK, and PF/JIS (JIS F 8801) for Japanese marine. Specifying the wrong thread is one of the most common first-time-buyer errors.
How to Match Thread to Market
Use these rules of thumb when the enclosure drawing is clear:
- New EU and most Asian industrial projects: Metric.
- North American panels and NEC-oriented specs: NPT.
- Existing European machines still punched for PG: keep PG; do not “upgrade” to Metric without re-tapping or changing the entry.
- UK / hydraulic-style parallel pipe entries: confirm G vs NPT on the drawing.
- Japanese marine and JIS-specified work: PF under JIS F 8801.
When drawings conflict—or when a global BOM mixes regions—list thread type as a mandatory line item next to cable OD and IP rating. Do not leave it as “standard gland.” Adapters exist, but every adapter is another joint, another seal, and another point of failure under vibration or wash-down.
Common Thread Mistakes (and How to Avoid Them)
Assuming similar major diameter means compatibility. PG11 and M20 are often compared in conversion tables, but pitch and profile differ. They are not substitutes.
Treating NPT and G as the same “inch thread.” One is tapered, one is parallel. Cross-threading or incomplete engagement is common when the wrong series is ordered.
Ordering Metric for a North American enclosure because “Metric is international.” International availability does not override the hole already in the panel.
Ignoring locknut and thread length. Thin panel walls, thick doors, and recessed entries need enough thread engagement and the correct locknut. Thread type alone is not enough if the body length is wrong.
Skipping the cable OD check after fixing the thread. Correct thread with wrong clamping range still leaks. Use the Cable Gland Sizing Guide once the thread standard is locked.
Thread Type in the Full Selection Process
Thread is one of seven factors that must line up: environment, IP rating, cable outer diameter (and armour diameter if present), thread type and entry size, material, certifications, and expected service life. Outdoor and wash-down applications still need the correct IP rating after the thread is chosen—see IP68 Cable Gland Explained and How to Choose the Right Cable Gland for Outdoor Electrical Enclosures.
Material choice (brass, nylon, stainless) is independent of thread series: the same Metric or NPT form is offered in multiple materials. For a side-by-side material comparison, see Brass vs Nylon vs Stainless Steel.
Frequently Asked Questions
What does PG, NPT, and Metric mean on a cable gland?
They name the entry thread standard. Metric (ISO 965) is parallel and dominant in Europe and much of Asia. NPT (ANSI B1.20.1) is tapered and common in North America. PG (DIN 40430) is a legacy German parallel thread still found on older equipment. Always match the gland thread to the enclosure entry—do not mix standards.
Can I use a Metric cable gland in an NPT hole?
No. Metric is parallel; NPT is tapered. The profiles and pitches are not compatible. Forcing them damages threads and compromises the enclosure seal. Order the thread series specified on the enclosure drawing, or change the entry with a proper, approved method—not a mismatched gland.
Is PG the same as Metric?
No. PG uses a different flank angle and pitch under DIN 40430. Conversion tables show approximate size relationships for planning only. For new designs, prefer Metric unless the existing panel is already PG.
What thread do Japanese marine cable glands use?
Many Japanese marine applications specify PF thread under JIS F 8801, often with 316 stainless for saltwater service. Confirm the vessel or equipment standard before ordering. Details are covered in the JIS marine cable gland guide.
Matching cable gland thread types to the enclosure is a specification decision, not a catalog afterthought. Identify Metric, NPT, PG, G, or PF from the drawing, then lock cable OD, material, and IP rating. Browse Metric, PG, NPT, and related options in the XingWei cable gland range, or request a quote with thread type, cable OD, material, and IP target so the part can be checked before order.