A multi-hole cable gland (also called a multi-cable or multi-entry gland) seals several cables through a single enclosure entry. One body and locknut replace a row of single glands when space on the panel is limited or when a group of small cables shares the same route into the box.
Used correctly, a multi-hole gland saves cut-outs and keeps a clean IP seal. Used incorrectly—wrong hole count, cables outside the seal range, or mixed diameters that never compress evenly—it becomes a leak path. This guide explains when multi-hole glands make sense, how to size them, and what to avoid.
For single-cable selection basics, see What Is a Cable Gland? and the Cable Gland Sizing Guide.
What Is a Multi-Hole Cable Gland?
A multi-hole gland has one threaded body that mounts in a single panel hole, and a sealing insert with two or more openings. Each opening is sized for a defined cable outer-diameter (OD) range. When the compression nut is tightened, the elastomer closes around every cable in its hole at the same time.
Typical configurations include 2, 3, 4, or more holes in one insert. Some designs use split or modular inserts so cables can be fitted without full threading from the free end. Materials are usually nickel-plated brass or stainless steel for industrial panels; nylon multi-hole variants appear on lighter-duty and plastic enclosures.
Product example: XingWei nickel-plated brass multi-hole cable gland (XW-DK series), IP68.
When Multi-Hole Glands Make Sense
- Limited panel space — dense control cabinets, small junction boxes, or gland plates with no room for individual entries.
- Groups of similar small cables — several instrument, sensor, or signal cables of the same OD entering together.
- Cleaner external layout — one entry instead of a cluster of small glands on outdoor boxes.
- Retrofit — an existing large knockout that must accept multiple thin cables without blank plates and adapters.
Multi-hole glands are a packaging choice, not a substitute for correct IP rating, thread match, or cable OD. Each hole still has a clamping range; cables outside that range will not seal.
When to Prefer Single Glands Instead
- Mixed cable diameters — one thick power cable and several thin signals rarely share one insert successfully.
- Frequent single-cable changes — replacing one core in a multi-hole insert can disturb the seal on the others.
- Armoured or EMC-screened cables — SWA/AWA needs double-compression armour clamps; screened VFD cable often needs 360° EMC contact. Multi-hole inserts are usually for unarmoured, unscreened (or simply jacketed) cables. See the Armored Cable Gland Guide and EMC Cable Gland Guide.
- High pull-out or vibration on one cable only — a dedicated single gland gives clearer strain relief per cable.
- Hazardous-area certified entries — use only glands whose certificate explicitly covers the multi-hole arrangement you plan to fit.
How to Size a Multi-Hole Gland
1. Count the cables that will share the entry now—and any spare holes you truly need. Empty holes must be closed with the manufacturer’s blank pins or plugs; an open hole in the insert voids the seal.
2. Measure every cable OD on the finished jacket. All cables must fall inside the published range for their holes. Do not force a cable that is too large; do not leave a hole “almost closed” on a cable that is too small.
3. Match hole pattern to the insert — same-diameter holes vs mixed-diameter inserts. Order the insert that matches your cable set; do not assume any multi-hole body accepts any OD mix.
4. Confirm thread and entry hole — Metric, NPT, PG, or other, same rules as single glands. Wrong thread still destroys the panel-side seal.
5. Check IP rating and material for the environment (indoor, outdoor, wash-down, coastal). Multi-hole does not automatically mean a higher or lower IP; performance depends on correct assembly and the datasheet rating.
Installation Notes
General waterproof install practice still applies: square body, entry washer where required, measured torque, seal on the outer sheath only. See How to Install a Waterproof Cable Gland.
Extra points for multi-hole:
- Feed all cables before final compression so the insert is not distorted by late additions.
- Keep cables parallel through the insert; sharp side-load on one hole can open a leak path on another.
- Fit blanking pins in every unused hole before torque.
- Do not over-torque in an attempt to “close gaps” on undersize cables—replace the insert or change to single glands instead.
If water appears after install, check OD match and blanking first, then torque and entry washer—see Cable Gland Leaking Water? and installation mistakes that cause IP68 ingress.
Common Specification Mistakes
- Counting cores instead of cables — a multi-core cable is still one jacket and usually needs one hole (or a single gland).
- Leaving spare holes open — every open hole is an ingress path.
- Mixing ODs in a same-size insert — the large cable prevents full compression on the small ones.
- Using multi-hole as a cheap substitute for an EMC plate — without 360° shield contact, screened cables are not terminated for EMC.
- Ignoring future maintenance — pulling one cable later may require loosening the whole gland and resealing all holes.
Multi-Hole vs Multiple Single Glands
| Multi-hole gland | Multiple single glands | |
|---|---|---|
| Panel cut-outs | One | One per cable |
| Best cable set | Several similar ODs | Any mix of ODs |
| Service one cable | May disturb others | Independent |
| Armour / EMC | Usually not | Available per cable |
| Spare capacity | Blank pins required | Blanking plugs on spare holes |
Choose multi-hole for space and cable similarity. Choose single glands for flexibility, armour, EMC, or frequent individual replacement.
Frequently Asked Questions
What is a multi-hole cable gland?
A multi-hole cable gland is a single entry fitting with a sealing insert that accepts two or more cables. One body mounts in one panel hole; each cable sits in its own hole in the elastomer and is sealed when the compression nut is tightened.
Can I leave some holes empty in a multi-hole gland?
Only if you close them with the blanking pins or plugs specified by the manufacturer. An open hole prevents the assembly from achieving its rated IP seal.
Can cables of different diameters share one multi-hole gland?
Only if the insert is designed with different hole sizes that match each cable OD. A single-size multi-hole insert requires all cables to fall within the same clamping range.
Are multi-hole glands IP68?
Many industrial multi-hole glands are rated IP68 when correctly assembled with the right cable ODs and blanked spare holes. The rating is not automatic—follow the datasheet ranges and install steps. For IP rating meaning, see IP68 Cable Gland Explained.
Multi-hole cable glands reduce cut-outs when several similar cables enter the same point. Size every hole to measured jacket OD, blank unused openings, and keep armour or EMC needs on dedicated single glands. Explore options such as the XingWei XW-DK multi-hole series in the cable gland category, or request a quote with cable count, each OD, thread, and IP target.