A cable gland and a cable connector solve different problems. A cable gland seals and secures a cable where it enters an enclosure. A cable connector joins two cables—or a cable to a device—so power or signal can pass. Mixing up the terms leads to incomplete bills of materials: a connector without a gland still leaves the box entry open; a gland alone does not mate two cable ends.
This article defines both parts, compares them side by side, and shows when you need one, the other, or both on the same installation. For a full buyer’s overview of glands, see What Is a Cable Gland?.
What Is a Cable Gland?
A cable gland (also called a cable fitting or cord grip in some markets) is a mechanical entry device. It threads or locks into an enclosure wall, compresses an elastomer onto the cable jacket, and provides strain relief so pull-out force does not reach the terminals. Under IEC 62444, glands are tested for retention and for maintaining the integrity of the entry.
Typical functions:
- Environmental sealing (dust and water) to support the enclosure’s IP rating
- Strain relief on the outer sheath
- Optional armour clamp on SWA/AWA cable
- Optional 360° shield bond on EMC glands
Glands do not “connect” conductors to each other. Conductors are still terminated on terminal blocks, PCBs, or device lugs inside the box. Browse types in the XingWei cable gland range.
What Is a Cable Connector?
A cable connector is an electromechanical interface that joins circuits. Examples include industrial circular connectors, rectangular multi-pin connectors, power plugs and sockets, and photovoltaic connectors such as MC4-style pairs. The connector provides contact surfaces, insulation, coupling (thread, bayonet, or latch), and often its own environmental rating when mated.
Typical functions:
- Conduct power or signal across a join
- Allow disconnection for maintenance or modular build
- Maintain contact pressure and insulation between poles
A connector may be free-hanging (inline) or panel-mounted. A panel-mounted connector still occupies an enclosure cut-out; whether that cut-out stays sealed depends on the connector’s flange design and gasket—not on a separate gland unless the design uses a gland-style back shell.
Side-by-Side Comparison
| Cable gland | Cable connector | |
|---|---|---|
| Primary job | Seal and clamp cable at enclosure entry | Join circuits (cable–cable or cable–device) |
| Conductors | Pass through; terminated elsewhere | Mated through contact pins/sockets |
| Disconnect | Not intended as a daily unplug point | Often designed to couple/uncouple |
| IP focus | Enclosure entry + jacket seal | Mated interface + housing |
| Typical standards | IEC 62444, IEC 60529 (IP) | Product family standards (e.g. industrial circular, PV) |
| Example | M20 brass IP68 gland on a control panel | Circular connector on a sensor lead; MC4 on a PV string |
In short: the gland protects the box; the connector completes the circuit path between two sides.
When You Need a Gland Only
Use a cable gland when cable runs continuously into an enclosure and is terminated on terminals or equipment inside—no intermediate mate/unmate joint at the wall.
- Control panels and PLC cabinets
- Motors with flying leads into a terminal box (where no plug is specified)
- Outdoor junction boxes and combiner boxes
- EV charger supply entries and site distribution cabinets
Selection still follows cable OD, thread, material, and IP rating—see sizing, installation, and outdoor guides on the blog.
When You Need a Connector Only
Use a connector when the design requires a breakable joint: tool-change, modular skids, field-replaceable sensors, or PV module stringing in free air.
- Inline joins between two flexible cables
- Sensor and actuator quick-disconnects
- Module-to-module PV connectors on the array (before the cable enters a combiner)
An inline connector in free air does not seal an enclosure. If that same cable later enters a box, you still need a gland (or a sealed bulkhead connector designed for panel mount) at the wall.
When You Need Both
Many systems use both on the same circuit, at different points:
- PV string — MC4-style connectors between modules; cable glands where strings enter the combiner box.
- Machine with pluggable field devices — circular connectors at the device; glands or bulkhead connectors where trunks enter the main cabinet.
- Portable equipment — connector at the umbilical; gland or sealed inlet on the fixed enclosure.
Buying only connectors for a panel build leaves every cable hole as a leak path. Buying only glands does not create a mateable interface where the drawing calls for one.
Terms That Cause Confusion
“Cable connector” used for glands. Some catalogues and non-English translations label glands as cable connectors. Check the product photo and datasheet: if there are no pins and the part only clamps a jacket into a threaded body, it is a gland.
Cord grip / strain relief bushing. Often the same family as glands, sometimes lighter-duty plastic. Still an entry device, not a multi-pin connector.
Bulkhead connector. A connector that mounts through a panel and seals the cut-out with its own flange gasket. It can replace a gland-plus-internal-terminal arrangement when a disconnect at the wall is required—but it is still a connector, specified by contact layout and coupling type.
EMC or armored “connectors.” Marketing language sometimes blurs names. EMC and armored products in the XingWei sense are still glands with extra shield or armour functions—see the EMC Cable Gland Guide and Armored Cable Gland Guide.
Practical Specification Tips
- On the BOM, list glands with thread, clamping range, material, and IP; list connectors with series, poles, voltage/current, and mating part numbers.
- For every enclosure hole, name the sealing method: gland, blanking plug, or sealed bulkhead connector.
- Do not assume a high IP connector rating covers a separate unsealed cable entry on the same box.
- After install, verify gland torque and connector engagement independently—see leaking water causes if ingress appears at an entry.
Frequently Asked Questions
Is a cable gland the same as a cable connector?
No. A cable gland seals and clamps a cable at an enclosure entry. A cable connector joins electrical circuits so they can mate and often unmate. They are different components with different standards and datasheet fields.
Do I need a cable gland if I already have connectors?
If the cable enters an enclosure through a plain hole, yes—you still need a gland or another sealed bulkhead arrangement. Connectors in free air (for example PV string connectors) do not seal the combiner or inverter wall by themselves.
Can a cable gland carry power like a connector?
Conductors pass through a gland and are terminated on separate terminals or equipment. The gland is not a multi-pin mated interface and is not rated as a connector contact system. Current-carrying capacity is determined by the cable and the terminations, not by the gland as a “connector.”
What is the difference between a cord grip and a cable gland?
Cord grip is often used interchangeably with cable gland, especially for plastic strain-relief entries. In industrial specifications, “cable gland” usually implies a product tested to gland standards (such as IEC 62444) with defined clamping and sealing performance. Always read the datasheet rather than relying on the trade name alone.
Use a cable gland to protect the enclosure entry; use a cable connector to join circuits. Most industrial and outdoor systems need the right gland on every cable hole—and connectors only where the design requires a mated joint. Explore sealing and strain-relief options in the XingWei cable gland category, or request a quote with cable OD, thread, material, and IP target for your enclosures.