Ceritified

ISO9001, CE, TUV ,CB, RoHS

Product Range

5000+ Specifications

Services

ODM & OEM

An EMC cable gland is a metal cable entry that seals the cable and bonds the cable shield (braid or foil) to the enclosure over a full 360° contact path. On variable-frequency drives (VFDs), servo systems, and noisy control panels, that bond gives high-frequency interference a short route to ground so it is less likely to couple into signal and control circuits.

A standard waterproof gland can provide IP sealing and strain relief without touching the screen. An EMC gland adds a spring, clamp, or cone that bites the shield while the outer seal still closes on the jacket. This guide explains when that extra function is required, how it differs from a normal gland, and what to specify on the bill of materials.

For general gland types and IP ratings, see What Is a Cable Gland? and IP68 Cable Gland Explained.

What “EMC” Means on a Cable Gland

EMC stands for electromagnetic compatibility: equipment should not emit excessive interference and should tolerate the interference around it. Screened (shielded) cables are one control measure. The screen only works well if it is terminated with low impedance at the entry—ideally a continuous 360° connection to the metal enclosure, not a single pigtail wire to a random earth point.

An EMC cable gland is built for that termination. Typical features include:

Nylon glands are insulating by design. They can seal a cable, but they cannot form a metal 360° shield bond. For EMC duty you normally specify a metal EMC gland, not a plastic waterproof gland with the screen left floating or pigtailed.

How 360° Shield Contact Works

Assembly usually follows this logic (exact strip lengths and order come from the datasheet):

  1. Strip the outer jacket to expose a defined length of braid or foil.
  2. Fold or dress the shield so it sits under the EMC spring or clamp—not under the outer elastomer alone.
  3. Tighten the EMC stage so the contact element closes around the full circumference of the screen.
  4. Compress the outer seal onto the intact jacket for IP performance and strain relief.
  5. Secure the body to the earthed metal enclosure with the locknut so the shield–gland–panel path is continuous.

A long pigtail from the braid to an earth bar adds inductance and can radiate at high frequency. 360° termination at the entry is the preferred practice in most VFD and EMC installation guides. The gland does not replace correct cable selection or drive filtering; it is one part of the wiring method.

When You Need an EMC Gland

Specify EMC glands when screened cable enters a metal enclosure and high-frequency noise control matters. Typical cases:

You can often use a standard waterproof gland when the cable is unshielded, the enclosure is plastic (no metal bond path), or the circuit is low-speed and the project EMC plan does not require 360° entry bonding. When in doubt, follow the drive or cable manufacturer’s installation manual—many explicitly call for 360° glands or EMC plates at the cabinet wall.

EMC Gland vs Standard Waterproof Gland

FeatureStandard waterproof glandEMC gland
Outer jacket seal (IP)YesYes
Strain reliefYesYes
360° shield bondNoYes
Typical bodyNylon or metalMetal (brass / stainless)
Best forUnshielded cable, general IP dutyScreened cable, VFD / EMC panels

IP rating and EMC function are independent. An EMC gland can still be IP68 when installed correctly; a high IP rating alone does not make a gland “EMC.”

How to Select an EMC Cable Gland

1. Cable shield diameter and jacket OD — The contact range must fit the exposed braid/foil diameter; the outer seal range must fit the jacket. Measure both. Sizing discipline is the same as for other glands—see the Cable Gland Sizing Guide.

2. Thread and entry — Match Metric, NPT, PG, or other thread to the enclosure hole. Wrong thread destroys the panel-side seal regardless of EMC performance.

3. Material — Nickel-plated brass is the usual industrial default. Stainless steel for corrosive or wash-down environments. The panel should be metal (or a metal EMC plate) so the bond has somewhere to go.

4. IP rating — Choose IP66/IP67/IP68 from the real exposure of the cabinet, same rules as other outdoor entries.

5. Armour vs screen — Cable armour (SWA/AWA) and EMC screen are different layers. Armoured power cable may need a double-compression gland for armour; screened VFD cable needs EMC shield contact. Some specialist glands combine functions—read the datasheet; do not assume one product covers both. For armour-only duty, see the Armored Cable Gland Guide.

6. Installation quality — 360° contact fails if the braid is sparse under the spring, painted over, or reduced to a pigtail. Follow strip length and torque from the manufacturer. General install practice is covered in How to Install a Waterproof Cable Gland; EMC glands add the shield stage before or with the outer seal as the drawing shows.

Common EMC Gland Mistakes

Frequently Asked Questions

What is an EMC cable gland?

An EMC cable gland is a metal cable entry that provides environmental sealing and a 360° electrical connection between the cable shield and the enclosure. It is used to improve electromagnetic compatibility on screened cables, especially with variable-frequency drives and sensitive control equipment.

Do I need an EMC gland for every shielded cable?

Not always. Use EMC glands where the installation method or equipment manual requires 360° shield termination at the enclosure wall. For some low-frequency signal cables a different bonding method may be specified. Follow the cable and equipment manufacturer’s EMC instructions.

Can a plastic cable gland be used for EMC?

A plastic gland cannot create a conductive 360° path to a metal panel. Shield bonding would depend on a separate pigtail or clamp inside the box, which is usually inferior at high frequency. Specify a metal EMC gland for 360° entry bonding.

Is an EMC cable gland waterproof?

Many EMC glands are designed for IP66, IP67, or IP68 when the outer seal is correctly sized and torqued. Check the datasheet for the rating and installation conditions. EMC contact and IP sealing are separate functions in the same assembly.


An EMC cable gland pairs jacket sealing with 360° shield bonding so screened cables can meet the wiring method expected on VFD and high-noise panels. Select by shield and jacket diameters, thread, metal body material, and IP need—and install so the braid sits fully under the contact spring, not as a long pigtail. Explore metal EMC options such as the XingWei shielded EMC gland (M20–M63) in the cable gland range, or request a quote with cable type, shield OD, jacket OD, thread, and IP target.

Leave a Reply

Your email address will not be published. Required fields are marked *

Get A Free Quote